爽到高潮漏水大喷视频软件

<output id="her55"><strong id="her55"><dl id="her55"></dl></strong></output>
<p id="her55"><label id="her55"><xmp id="her55"></xmp></label></p>
  1. <table id="her55"><ruby id="her55"></ruby></table><td id="her55"></td><table id="her55"><span id="her55"></span></table>
    1. <td id="her55"></td>
    2. <p id="her55"></p>

        1.  

           
             
             
           
           
           
           
           
           
           



          Troubleshooting Tearout With Maple Flooring

                Check sharpening, settings, feed rates, and more. April 10, 2005

          Question
          We have a 276 and are running wide soft maple flooring with 6" three blade straight knives. Every so often it will tear or chip out leaving a product so rough we can't sell it. We have tried to slow it down with some success but it still is a problem. We have done everything we can think of to stop this problem, including changing the pressure shoe, sharpening the knives, checking for play in the outboard bearings, and running as tight and slow as possible. We also have some mill marks that are a pain to deal with. Help.

          Forum Responses
          (Solid Wood Machining Forum)
          From Dave Rankin, technical advisor:
          Tearout comes from several possible things. If this problem is somewhat sporadic I would discuss the problem with the people that dry your lumber. Many drying companies will rush the time in the kiln and the wood suffers because of it. This lack of proper conditioning will result in more tearout than normal. Second it is possible that the grain in the wood is more likely to tearout due to nature. Some wood has tighter grain while other wood will be looser grain.

          Tearout can also be increased with reduced holddown control. The work piece needs to be held secure with all of the holddowns. Sharp tools are required. Some of the information that you did not provide:

          Hook angle of the head - recommended 5-12 degree
          Back clearance angle - recommended 20-22 degree
          Side clearance angle - recommended not to exceed 5 degree.
          Jointed or non-jointed finish - if jointed, the land on the knives must be less than 1/64" to provide a good finish.
          Feed rate - this will vary according to the number of knives that are jointed.
          RPM of the spindles - this will help in determining the feed rate.

          After you have exhausted all of your options you may then consider special tooling. The use of shear angle heads has proven to reduce tearout in many maple applications.



          From contributor A:
          I agree that some woods are more prone to tear out. On maple itís not uncommon to get the tear outs around knots where the direction of the grain changes. Also changing the hook will help like Dave suggested. You mentioned mill marks though. To me, that indicates youíve got more than wood characteristic issues going on. And any issue that can cause chatter or mill marks can also cause tear out. To see if your pressure shoe is adjusted correctly, first set up on a piece of 6" s4s. Run the piece half way through your machine and shut it off. Then take a feeler gauge (.005) and try to stick it between the shoe and the wood all around where the two make contact. If you find a gap, you have a clue what your problem is. Also try to stick it under the board between the bedplates and the wood (I realize you can only do this on the outside).


          From the original questioner:
          Thanks for the answers. It looks like I have a bunch of things to correct. I have the wrong hook angle on the heads 20 degrees. I have run the pressure shoe thru the jointer and it seems ok but I will check with the gauge. I guess I will be looking for some used 12 degree heads. Thanks for all the help.

          Would you like to add information to this article?
          Interested in writing or submitting an article?
          Have a question about this article?


          Have you reviewed the related Knowledge Base areas below?
        2. KnowledgeBase: Knowledge Base

        3. KnowledgeBase: Architectural Millwork

        4. KnowledgeBase: Architectural Millwork: Flooring

        5. KnowledgeBase: Architectural Millwork: Moldings

        6. KnowledgeBase: Architectural Millwork: Stock Manufacturer

        7. KnowledgeBase: Solid Wood Machining

        8. KnowledgeBase: Solid Wood Machining: General

        9. KnowledgeBase: Solid Wood Machining: Setup and Maintenance

        10. KnowledgeBase: Solid Wood Machining: Tooling

        11. KnowledgeBase: Solid Wood Machining: Tool Grinding


          Would you like to add information to this article? ... Click Here

          If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to
          review our Forum Guidelines.

          Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB's Site Map.

          When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.

          Return to beginning of article.



          Refer a Friend || Read This Important Information || Site Map || Privacy Policy || Site User Agreement

          Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.

          Contact us to discuss advertising or to report problems with this site.

          To report a problem, send an e-mail to our Webmaster

          Copyright © 1996-2021 - Woodweb.com
          All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
          Review Woodweb.com's Copyright Policy.

          The editors, writers, and staff at Woodweb.com try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at Woodweb.com after considerate evaluation, and at their own risk.

          Woodweb.com
          865 Troxel Road
          Lansdale, PA 19446

          Contact Us











        12. WOODWEB - the leading resource for professional woodworkers


            Home » Knowledge Base » Knowledge Base Article
           
          爽到高潮漏水大喷视频软件
          <output id="her55"><strong id="her55"><dl id="her55"></dl></strong></output>
          <p id="her55"><label id="her55"><xmp id="her55"></xmp></label></p>
          1. <table id="her55"><ruby id="her55"></ruby></table><td id="her55"></td><table id="her55"><span id="her55"></span></table>
            1. <td id="her55"></td>
            2. <p id="her55"></p>